left right

Dobrodošli na Player e-shop!


Garancija najnizih cena

pobedićemo svaku konkurentsku cenu!


D&R

AIRLAB MKII

Šifra Proizvoda: 6420

Napiši prvi komentar za ovaj proizvod





11719 €

Dostupnost:

Uskoro na lageru, proverite mogućnost porudžbine Proverite mogućnost porudžbineMogućnost porudžbineUkoliko je za proizvod naznačeno da će ga biti uskoro lageru, znači da proizvod trenutno nemamo u prodavnici, ali ga je moguće naručiti.
Molimo Vas da proverite detalje u vezi mogućnosti rezervacije ovog proizvoda.

Proveru možete izvršiti putem telefona:
011/33-47-615
011/33-47-442
011/37-39-701
011/37-74-968


ili emailom:
info@player.rs


Prikazana cena je za komad.

Kratak opis

10 Triple Inputs + 2 Telco modules, 4 blanks and 4x VU meters. Special offer for this popular configuration !!! The AIRLAB MK2 radio ON-AIR console is an extremely reliable solution for applications where features and functions has to be weighed up against operational simplicity. It\\\'s analog, digitally controlled signal path is the best solution of both worlds to achieve a reliable workhorse under any condition. With over 600 units in the field, the Airlab MK2 has proven to be a successful centerpiece of your ON-Air studio. A simple direct accessible control surface combined with intelligent instantly reset able digital functions enables customizing to station requirements...

11719 €

Pogledaj proizvod iz više uglova:


*Istaknute cene su informativnog karaktera.
Pre svake kupovine i poručivanja ovog uređaja, pozovite jednu od Player prodavnica putem navedenih brojeva telefona, kako biste dobili najbolju cenu.

10 Triple Inputs + 2 Telco modules, 4 blanks and 4x VU meters. Special offer for this popular configuration !!!

The AIRLAB MK2 radio ON-AIR console is an extremely reliable solution for applications where features and functions has to be weighed up against operational simplicity. It\\\'s analog, digitally controlled signal path is the best solution of both worlds to achieve a reliable workhorse under any condition.

With over 600 units in the field, the Airlab MK2 has proven to be a successful centerpiece of your ON-Air studio.

A simple direct accessible control surface combined with intelligent instantly reset able digital functions enables customizing to station requirements and even to personal requirements because of the use of a personalized chip card holding all important functional data. Purchasing choices are straightforward: the welded steel frame will accommodate a maximum of 16 triple input modules, which could include an unlimited number of Telco modules (up to 16 of course) plus the master section with script space. The main outputs are electronically balanced and the majority of connectors are on balanced XLRs.

TRIPLE INPUT MODULE.

As the name suggests, the AIRLAB MK2 triple input module combines a mic input with two stereo line inputs.
The mic input is electronically balanced with the industry standard SSM 2017 low noise mic pre-amp.
A 48 volt phantom power switch is provided for. Apart from the gain control we have built in a front panel accessible trimmer to determine the mic gain range.
A low cut filter can be activated by a jumper on the PCB. The mic input is located at the back of the console on female XLR connectors.
The unbalanced stereo line B input, accessible on Cinch connectors, can be fitted with an RIAA plug-in PCB to accept phono players.
The Line A input is balanced and on XLR’s.
The fixed, to +/- 12dB limited three band equalizer is followed by a SUB and PROGRAM assign switch that routes signals to both outputs allowing production work to be carried out during broadcast.
The stereo Aux. control can be selected pre or post VCA/MUTE, depending on jumpers.
The stereo Aux. send is followed by a Pan control, a Cue/select switch and the channel On switch disabling
Cue, although it can be reactivated while the channel is on.
It is also possible to activate Cue via the channel remote connector.
Cue becomes a Cough facility when the Mic input and the \\\'On-AIR\\\' status is selected.
The AIRLAB MK2 is equipped with linear 100mm faders controlling high quality \\\'THAT\\\' VCA\\\'s, another high end industry standard.
Start can be activated with the fader or ON switch, depending which is activated first.
Start can be software configured so that switching is from line A or line B. Similarly, the Cue switch is under software control avoiding impossible settings.

TRIPLE INPUT MODULE NO EQ.

This module is equivalent to the standard module with EQ, but lacks the EQ controls. Mostly advised for ON-AIR applications.

TELCO MODULE.

The AIRLAB MK2 has the possibility to be loaded with up to 16 Telco modules.
Due to an ingenious Mix-Minus system alignment is only necessary during installation.
The AIRLAB MK2 Telco module is a straight forward design making communication very easy.
The first control is the front panel accessible, trimmer for side tone adjustment, only necessary during installation.
The Telco Send knob controls the outgoing signal to the caller. This signal is derived from the PROGRAM or SUB bus.
The line input can be switched to a balanced XLR input connector to accept an external (digital) hybrid instead of its own internal hybrid.
A separate input gain control with HP and LP filters be used to enhance intelligibility.
The SUB and PROGRAM assign switch routes the signal to both outputs if needed.
The stereo Aux. control has jumpers that select its source to be pre or post VCA/MUTE.
A Pan-pot and CUE/Select switch plus the ON switch completes the Telco module.
A 100mm linear fader controls a high quality THAT VCA, eliminating any fader wear out in the future.
Connecting a Caller can be accomplished with the ON switch when the fader is up or with the CUE/SELECT/RING switch when the fader is down.
When CUE is active in the TELCO module, the caller is connected to the CUE bus and also the engineers talk-back, but does not go ON-AIR yet as the fader is down.
It is possible to connect both the Cue and On switch to a remote unit, allowing a director to control the broadcast.
A \\\'Connect\\\' LED positioned below the High Cut switch indicates that the internal Hybrid is active.

MASTER

The master module is divided in three sections. The first \\\'module\\\' houses the TAPE SEND which selects the feed to the tape output.
This could be either the SUB output signal or the AUX. output signal..
The stereo Aux. master controls the outgoing Aux. signals from the input modules. A Talk-back to AUX. switch is provided for.
The lower part of this \\\'module\\\' houses the Control Room Monitor section that can be fed by an EXT(ernal) stereo input, the stereo Aux output, a stereo On-Air signal or the stereo SUB output signal. All selections have LED indicators and the lowest positioned switch has priority over the input selectors positioned directly above.
The CUE balance pot adjusts the balance between the PROGRAM output or another selected input source and the CUE signal (when selected).
A cue LED indicates when a CUE signal is on the CRM or Phones.
Separate Phones and CRM controls, with a DJ mic on mute indicator on the CRM, complete this \\\'module\\\'.

COMMUNICATION IS ON BOARD.

The second \\\'module section\\\' houses the Talk back level control for the electret microphone and the Studio section, usually used to monitor the PROGRAM output, with the ability to switch to from Air, from SUB or the Control Room Monitor signal.
When the studio mic is open the studio output is muted, indicated by the studio MUTE LED. The studio output is fitted with a Talk-back switch Communication is very important in broadcast studio’s, so we decided to go for three separate outputs. One for Studio, one for Guest\\\'s) and one for the Announcer.
All outputs receive the same signal that is selected by the input selection switches, or the Program output signal when no switch is activated.
The Studio output has a mute LED indicator when the output is muted.
All three outputs have a direct Talk back access switch for instant communication between control room and presentation area.
The Cue buss is the main communication buss in the console. When a listener calls the station, by pushing the Cue switch of the Telco module you have him or her directly on the control room monitors. At the same time the internal electret microphone is activated so you can immediately respond.
The announcer can depress his remote communication button and is linked to the same Cue buss, so that is three of you talking with each other.
The AIRLAB has four VU meters of which two are always connected to the main outputs and the other two are following whatever is heard on the CRM.

SOFTWARE CONTROLLABLE SET-UP CAN BE STORED ON A CHIP CARD.

A specialty of the AIRLAB MK2 is its ability to program all sorts of internal settings and then save it to a personalized chip card for instant reset.

The following settings can be programmed:
* Module set as DJ mic input.
* Module set as Announcer mic input.
* Module set as Studio mic input.
* Start/Stop plus Pulse/Continue per module.
* Cue start active
* Fader start or \\\'ON\\\' start per module.
* External remote (inactive per module.
* Timer start pulse per module.
* On-Air control signal on/off per module.
* Auto communication Announcer on/off.
* Auto CUE reset on/off.
* Auto CUE on/off.

There is a Timer function built in the AIRLAB for time related measurements such as duration of an incoming/outgoing call. Timer set-up can be software controlled and stored. The AIRLAB MK2 is D&R’s latest addition to a growing series of broadcast consoles. Its high quality clean audio path with a minimum of hardware switches in the audiopath is your guarantee that this is a reliable radio console for daily broadcasts around the hour for many years to come.

SPECS

INPUTS
Mic inp. bal. 2kOhm - 128dBr (40dB gain range plus 30dB of trim range)
* Line inp. bal 10kOhm +/- 20dB gain range.
* Telco input (XLR) 10kOhm bal. 0dBu nominal.
* CARR: mic input max.. gain: 1kHz 85dB
* Line inp max.. gain 1 kHz 80dB

EQs
* +/- 12 dB @ 10kHz shelving
* +/- 12 dB @ 3kHz bell curve
* +/- 12 dB @ 60 Hz shelving
* Low Cut: 80Hz, 12dB per octave (mic only)
* Low Cut: 200Hz, 6 dB per octave (Telco only)
* High Cut: 8 kHz, 6 dB per octave (Telco only)

OUPUTS
* Frequency response: 20-20.000 Hz +/-0.5dB
* Harmonic distortion: 0.035% (VCA in, 2nd harm)
* Cross talk: less than -90dBr
* Noise: -86dBr
* Headroom: +22dB internal, 16dB on outputs
* Mix-Minus rejection: @1kHz -60dB
* Channel fader attenuation: 1kHz, 100dB

REMOTE
* All channel remotes are on stereo jack sockets.
* Start/Stop switching is by isolated reed relays.
* Both ON-AIR 1 and 2 (red light) outputs are isolated by relays.

DIMENSIONS
* AIRLAB: 50 kg / 110 Lbs
* Drop through mounting hole dimensions:
* 590mm x 775mm (depth x width)

 Scroll To Top